SJ 50976/18-2002 2.92系列(接微带)插针接触件螺纹安装、射频同轴插座连接器详细规范
作者:标准资料网 时间:2024-05-05 00:56:58 浏览:9471
来源:标准资料网
基本信息
| 标准名称： | 2.92系列(接微带)插针接触件螺纹安装、射频同轴插座连接器详细规范 |
| 英文名称： | Connectors receptacle coaxial radio frequency series 2.92 pin contact scred nounted for micro-strip detail specification for |
| 中标分类： |
电子元器件与信息技术 >>
电子元件 >>
连接器 |
| 发布部门： | 中华人民共和国信息产业部 |
| 发布日期： | 2002-10-30 |
| 实施日期： | 2003-03-01 |
| 首发日期： | 1900-01-01 |
| 作废日期： | 1900-01-01 |
| 提出单位： | 中华人民共和国信息产业部 |
| 归口单位： | 信息产业部电子第四研究所 |
| 起草单位： | 信息产业部电子第四研究所 |
| 起草人： | 吴正平、钟宝红 |
| 出版社： | 中国电子工业出版社 |
| 出版日期： | 2003-03-01 |
| 页数： | 3页 |
适用范围
本系列规范规定了2.92系列（接微带）射频同轴连接器的详细要求。本系列规范适用于2.92系列（接微带）系列射频同轴连接器。
前言
没有内容
目录
没有内容
引用标准
GJB 976-1990 同轴、带状或微带传输线用的射频同轴连接器总规范
SJ 50681/82-2002 292系列（接兰硬电缆）插针接触件2级射频同轴插头连接器详细规范
所属分类： 电子元器件与信息技术 电子元件 连接器
Product Code:SAE J2293/2
Title:Energy Transfer System for Electric Vehicles - Part 2: Communication Requirements and Network Architecture
Issuing Committee:Hybrid - Ev Committee
Scope:SAE J2293 establishes requirements for Electric Vehicles (EV) and the off-board Electric Vehicle Supply Equipment (EVSE) used to transfer electric energy to an EV from an electric utility power system (utility) in North America. This document defines, either directly or by reference, all characteristics of the total EV energy transfer system (EV-ETS) necessary to insure the functional interoperability of an EV and EVSE of the same physical system architecture. The ETS, regardless of architecture, is responsible for the conversion of AC electrical energy into DC electrical energy that can be used to change the storage battery of an EV, as shown.Product Code:SAE AS586
Title:Wheel and Brake (Sand and Permanent Mold) Castings Minimum Requirements for Aircraft Applications (NONCURRENT Jan 2005)
Issuing Committee:A-5a Wheels, Brakes And Skid Controls Committee
Scope:This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.
